Voltage Multiplier

Voltage Multiplier

                                We require high voltage at certain applications ,we see mosquito bats to kill mosquito , in that we produce a high voltage from a battery . we can use this circuit for making high voltage from a low voltage source         

This circuit produces a very high voltage and care must be used to prevent getting a nasty shock.  The transformer can produce over 1,000v and the 8-stage multiplier can produce up to 20,000v 

.

circuit diagram

Door bell circuit using NE555

Door bell circuit using NE555

The main part of this doorbell circuit are two NE555 timer ICs.When some one presses switch S1 momentarily ,the loud speaker sounds a bell tone as long as the time period of the monostable multivibrator built around IC1.






When the switch S1 pressed, IC1 is triggered at its pin 2 and output pin 3 goes high for a time period previously set by the values of POT R4 and POT R5.When the output ofIC1 goes high it resets IC2 and it starts to oscillate to make a bell sound through the speaker.The IC2 is configured as an astable multivibrator whose oscillation frequency can be varied with the help of POT R5.By adjusting the values of R4 & R5, modifications on the tone are possible.



Notes.

* The circuit has to assembled on a good quality PCB or common board.
* The IC1 & IC2 has to be mounted on IC holders.
* Power the circuit from a 9V battery or 9V DC power supply.
* Switch S1 is push button switch.

Water triggered alarm system with 555 timer

Water triggered alarm system with 555 timer

You can use this circuit for you water tank.then you can know before over flowing your tank.on the other hand you can use this circuit as a rain detector then you can know before rain comes.so I suppose this would be a so useful circuit for you

555 Timer as Monostable Multivibrator

555 Timer as Monostable Multivibrator

A monostable multivibrator (MMV) often called a one-shot multivibrator, is a pulse generator circuit in which the duration of the pulse is determined by the R-C network,connected externally to the 555 timer. In such a vibrator, one state of output is stable while the other is quasi-stable (unstable). For auto-triggering of output from quasi-stable state to stable state energy is stored by an externally connected capaci­tor C to a reference level. The time taken in storage determines the pulse width. The transition of output from stable state to quasi-stable state is accom­plished by external triggering. The schematic of a 555 timer in monostable mode of operation is shown in figure. 


Pin 1 is grounded. Trigger input is applied to pin 2. In quiescent condition of output this input is kept at + VCC. To obtain transition of output from stable state to quasi-stable state, a negative-going pulse of narrow width (a width smaller than expected pulse width of output waveform) and amplitude of greater than + 2/3 VCC is applied to pin 2. Output is taken from pin 3. Pin 4 is usually connected to + VCC to avoid accidental reset. Pin 5 is grounded through a 0.01 u F capacitor to avoid noise problem. Pin 6 (threshold) is shorted to pin 7. A resistor RA is connected between pins 6 and 8. At pins 7 a discharge capacitor is connected while pin 8 is connected to supply VCC.


555 IC Monostable Multivibrator Operation.






555 monostable-multivibrator-operation

For explain­ing the operation of timer 555 as a monostable multivibrator, necessary in­ternal circuitry with external connections are shown in figure.
The operation of the circuit is ex­plained below:

Initially, when the output at pin 3 is low i.e. the circuit is in a stable state, the transistor is on and capacitor- C is shorted to ground. When a negative pulse is applied to pin 2, the trigger input falls below +1/3 VCC, the output of comparator goes high which resets the flip-flop and consequently the transistor turns off and the output at pin 3 goes high. This is the transition of the output from stable to quasi-stable state, as shown in figure. As the discharge transistor is cut­off, the capacitor C begins charging toward +VCC through resistance RA with a time constant equal to RAC. When the increasing capacitor voltage becomes slightly greater than +2/3 VCC, the output of comparator 1 goes high, which sets the flip-flop. The transistor goes to saturation, thereby discharging the capacitor C and the output of the timer goes low, as illustrated in figure.

Thus the output returns back to stable state from quasi-stable state.

The output of the Monostable Multivibrator remains low until a trigger pulse is again applied. Then the cycle repeats. Trigger input, output voltage and capacitor voltage waveforms are shown in figure.
Monostable Multivibrator Design Using 555 timer IC

The capacitor C has to charge through resistance RA. The larger the time constant RAC, the longer it takes for the capacitor voltage to reach +2/3VCC.

In other words, the RC time constant controls the width of the output pulse. The time during which the timer output remains high is given as

tp = 1.0986 RAC
where RA is in ohms and C is in farads. The above relation is derived as below. Voltage across the capacitor at any instant during charging period is given as

vc = VCC (1- e-t/RAC)

Substituting vc = 2/3 VCC in above equation we get the time taken by the capacitor to charge from 0 to +2/3VCC.

So +2/3VCC. = VCC. (1 – e-t/RAC) or t – RAC loge 3 = 1.0986 RAC

So pulse width, tP = 1.0986 RAC s 1.1 RAC

The pulse width of the circuit may range from micro-seconds to many seconds. This circuit is widely used in industry for many different timing applications.

555 DC to AC inverter circuit diagram

555 DC to AC inverter circuit diagram

This is inverter circuit diagram.Here I have used famous Transistors TIP41 and TIP42.And the frequency is generated by NE555.By using R4 you can control the frequency.out put voltage is 120V-230V.the frequency is 50Hz.This circuit operates with 5V-15V.





Note

# Be careful because you are dealing with 230V.

#This circuit is not suitable for kids.

#Use heat sinks for transistors

NE 555 Pulse generator

NE 555 Pulse generator

Most of our members asked pulse generator circuits. so this is a simple and common circuit.and you can use this with your light circuit diagrams too.



Note

# Don't supply more than 15V

Simple 555 Timer circuit diagram

Simple 555 Timer circuit diagram

A lot of guys requested a simple timer circuit so this is the circuit.This circuit runs with main IC NE555. you can change the frequencies of the circuit by changing the values of R1, R2,C .This circuit runs with 4.5V.



Note :

# Don't supply more than 4.5V
# Build this on a PCB